Search results for "303"
showing 10 items of 6883 documents
A Model for High-Cycle Fatigue in Polycrystals
2018
A grain-scale formulation for high-cycle fatigue inter-granular degradation in polycrystalline aggregates is presented. The aggregate is represented through Voronoi tessellations and the mechanics of individual bulk grains is modelled using a boundary integral formulation. The inter-granular interfaces degrade under the action of cyclic tractions and they are represented using cohesive laws embodying a local irreversible damage parameter that evolves according to high-cycle continuum damage laws. The consistence between cyclic and static damage, which plays an important role in the redistribution of inter-granular tractions upon cyclic degradation, is assessed at each fatigue solution jump,…
Hybrid Equilibrium Finite Element Formulation for Cohesive Crack Propagation
2019
Equilibrium elements have been developed in hybrid formulation with independent equilibrated stress fields on each element. Traction equilibrium condition, at sides between adjacent elements and at sides of free boundary, is enforced by use of independent displacement laws at each side, assumed as Lagrangian parameters. The displacement degrees of freedom belongs to the element side, where an extrinsic interface can be embedded. The embedded interface is defined by the same stress fields of the hybrid equilibrium element and it does not require any additional degrees of freedom. The extrinsic interface is developed in the consistent thermodynamic framework of damage mechanics with internal …
Virtual Element Method: Micro-Mechanics Applications
2019
In this contribution we present an application of the lowest order Virtual Element Method (VEM) to the problem of material computational homogenization. Material homogenization allows retrieving material properties through suitable volume averaging procedures, starting from a detailed representation of the micro-constituents of the considered material. The representation of such microstructure constitutes a remarkable effort in terms of data/mesh preparation, especially when there is not evident microstructural regularity. For such a reason, computational micromechanics may represent a challenging benchmark for showing the potential of VEM. In this contribution, polycrystalline materials ar…
A Model for Low-Cycle Fatigue in Micro-Structured Materials
2019
A microscale formulation for low-cycle fatigue degradation in heterogeneous materials is presented. The interface traction-separation law is modelled by a cohesive zone model for low-cycle fatigue analysis, which is developed in a consistent thermodynamic framework of elastic-plastic-damage mechanics with internal variables. A specific fatigue activation condition allows to model the material degradation related to the elastic-plastic cyclic loading conditions, with tractions levels lower than the static failure condition. A moving endurance surface, in the classic framework of kinematic hardening, enables a pure elastic behaviour without any fatigue degradation for low levels of cyclic tra…
A Thermodynamically Consistent CZM for Low-Cycle Fatigue Analysis
2018
A cohesive zone model for low-cycle fatigue analysis is developed in a consistent thermodynamic framework of elastic-plastic-damage mechanics with internal variable. A specific fatigue activation condition allows to model the material degradation related to the elastic-plastic cyclic loading conditions, with tractions levels lower than the damage activation condition. A moving endurance surface, in the classic framework of kinematic hardening, enables a pure elastic behavior without any fatigue degradation for low levels loading conditions.
The filter and calibration wheel for the ATHENA wide field imager
2016
The planned filter and calibration wheel for the Wide Field Imager (WFI) instrument on Athena is presented. With four selectable positions it provides the necessary functions, in particular an UV/VIS blocking filter for the WFI detectors and a calibration source. Challenges for the filter wheel design are the large volume and mass of the subsystem, the implementation of a robust mechanism and the protection of the ultra-thin filter with an area of 160 mm square. This paper describes performed trade-offs based on simulation results and describes the baseline design in detail. Reliable solutions are envisaged for the conceptual design of the filter and calibration wheel. Four different varian…
Evaluation of nano/submicro pores in suspension plasma sprayed YSZ coatings
2019
Abstract Nano-submicro pores could considerably influence the coating performances and thus should be properly designed for the intended applications. However, it is challenging to characterize accurately such small pores in coatings. In this study, YSZ coatings were firstly manufactured by suspension plasma spray (SPS) and the nano-submicro pores in as-prepared coatings were investigated using Ultra-small-angle X-ray scattering (USAXS). Afterwards, a multivariate analysis on the effect of five different process parameters was carried out. The two main results showed that: 1) the nano-submicro pores content in coatings has a negative correlation with suspension mass load and powder size, an…
Spark Plasma Sintering of Metallic Glasses
2019
Spark plasma sintering (SPS) of metallic glasses (MG) can be quite different from sintering crystalline metallic alloys. Indeed, MG behave differently with increasing temperature, as they encounter a glass transition and devitrification. Their shaping can thus be compared to what can be performed on thermoplastic polymers. SPS is a promising way to prepare bulk parts from amorphous powders, since it allows very fast heating and cooling rates. It gives an advantage to avoid or limit devitrification of the amorphous phase upon the thermal cycle. However, diffusion mechanisms, which generally control densification, are activated at temperatures that are not compatible with MG structural integr…
APOGEE Data Releases 13 and 14: Data and Analysis
2018
Data and analysis methodology used for the SDSS/APOGEE Data Releases 13 and 14 are described, highlighting differences from the DR12 analysis presented in Holtzman (2015). Some improvement in the handling of telluric absorption and persistence is demonstrated. The derivation and calibration of stellar parameters, chemical abundances, and respective uncertainties are described, along with the ranges over which calibration was performed. Some known issues with the public data related to the calibration of the effective temperatures (DR13), surface gravity (DR13 and DR14), and C and N abundances for dwarfs (DR13 and DR14) are highlighted. We discuss how results from a data-driven technique, Th…
Estimation des incertitudes de mesure sur bras polyarticulé portable par méthode de Monte Carlo
2013
International audience; Les bras polyarticulés portables ont progressivement évolué et sont de plus en plus utilisés dans l’industrie. Cependant, à l’heure actuelle, la traçabilité de ces dispositifs est difficile à effectuer et les incertitudes de mesures relatives à l’utilisation de ces appareils ne sont pas quantifiées. Le travail mené consiste à déterminer les incertitudes de mesures associées à la quantification, par un bras polyarticulé portable, des caractéristiques géométriques et dimensionnelles d’une pièce mécanique. Les travaux visant à élaborer un modèle d’incertitude de mesure, sont basés sur la méthode de Monte Carlo du supplément 1 du Guide pour l'expression de l'incertitude …