Search results for "IT-SOFC"
showing 9 items of 9 documents
Direct Methane Oxidation on La1-xSrxCr1-yFeyO3-δ perovskite-type oxides as Potential Anode for Intermediate Temperature Solid Oxide Fuel Cells
2016
Abstract La1−xSrxCr1−yFeyO3−δ (x = 0, 0.1, 0.15, 0.2; y = 0, 0.3, 0.5) perovskite-type oxide powders were synthesized by solution combustion synthesis and characterized by X-ray diffraction, X-ray photoelectron spectroscopy and H2-temperature programmed reduction. Selected compositions were studied by CH4-temperature programmed reduction in the absence and in the presence of H2S. Temperature programmed oxidation and structural characterizations were performed in order to discriminate the nature of residual deposits on the catalyst surface. The study about reduction in different methane-based mixture revealed that total and partial methane oxidation occurred in the range ∼450–1000 °C indepen…
Structural, catalytic and electrical investigation on La1-xSrxCr1-yFeyO3- δ as anodes for IT-SOFCs
2012
FROM INTERCONNECTORS TO ANODE MATERIALS FOR IT-SOFCs:THE ROLE OF IRON IN La1-xSrxCr1-yFeyO3-δ
2013
The Effect of Ni Doping on the Performance and Electronic Structure of LSCF Cathodes Used for IT-SOFCs
2018
We investigated the effect of nickel doping on the electronic structure and performance of nanostructured La0.6Sr0.4Co0.2Fe0.8-0.03Ni0.03O3-delta prepared by the one-pot sol gel method. The commercial undoped La0.6Sr0.4Co0.2Fe0.8O3-delta (ISCF0.8) was used as reference. Moreover, for comparison, Ni (3 mol %) was deposited by wetness impregnation over the La0.6Sr0.4Co0.2Fe0.8O3-delta. We show by in situ X-ray absorption spectroscopy at 900 degrees C under air flow that nickel enters the B perovskite site of the material and favors the stabilization of the cobalt oxidation state, as evidenced by the delay in the decrease of the average Co valence with respect to undoped samples. Our results a…
New synthetic strategies for the enhancement of the ionic conductivity in Ce0.8Sm0.2O2-x
2013
Introduction Samarium-doped ceria has been widely investigat-ed for electrochemistry applications as full density elec-trolyte for intermediate temperature solid oxide fuel cells (IT-SOFC), between 500°C and 800°C [1]. One of the main challenges for the ceria-based electrolytes is to decrease the resistivity at the grain boundary zone, especially in this low temperature range. Microstructure and morphology of the powder play a fundamental role on the densification behaviour and grain boundary properties, thus affecting the overall conductivity of electrolytes [2]. In this light, solution combustion syn-thesis (SCS) represents a flexible method to produce ultra fine powders with suitable mic…
Nuovi materiali per celle a combustibile ad ossidi solidi a temperatura intermedia (IT-SOFC): sintesi, caratterizzazione e correlazione struttura-pro…
2014
Ceria-based electrolytes prepared by solution combustion synthesis: The role of fuel on the materials properties
2016
Ce0.8Sm0.2O2 â xpowders were synthesized by solution combustion synthesis using citric acid, cellulose and sucrose as single, or intimately mixed, fuels. The powders were characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, N2sorption at â196 °C, H2-temperature programmed reduction and thermogravimetric analyses. Textural properties of the powders were shaped by the peculiar employed fuel. The study of reducibility revealed that oxygen vacancies formation is mainly influenced by both parameters, specific surface area and total pore volume. The different tendency toward reduction played a key role in sintering under reducing atmosphe…
Manufacturing and characterization of single cell intermediate-temperature solid oxide fuel cells for APU in transportation application
2014
The fabrications of large area IT-SOFC planar cell by new simple and cost effective process were explained. The optimization of the new process with respect to pore formers, thickness of layers, sintering temperature were performed. The electrochemical results of 10cm2 performed in Fiaxell open flange set up were detailed with respect to different configuration. Long term ageing performance tests of single cells were conducted in Fiaxell device and results are discussed. Preparation of new test bench and stacking process performed till now were briefed.